SUPER FORTECA 121 01 01 ksiazeczka Ver E20 Eng, Centralne zamki
[ Pobierz całość w formacie PDF ]
USER’S MANUAL
1. FEATURES OF THE CAR SECURITY SYSTEM
-
two two-button transmitters with unique and dynamically modified code – code hopping
(KEELOQ
algorithm);
-
the driver identification function that secures a car against unauthorized starting up of the
engine,
-
the handling-free function to identify presence of a user inside the vehicle;
-
the PANIC function to deter a possible thief that attempts to tamper with a vehicle,
-
smart engine disable, the built-in single-circuit immobilizer,
-
the second-channel output that enables separate remote trunk release function,
-
actuation of any type of a central lock – both electric and pneumatic ones (1/3 sec.),
-
actuation of window roll-up modules from the 1 /3 /35 sec. output,
-
the programmable COMFORT function, remote anti-carjacking central lock activation while
driving,
-
loud or silent signalling of alarm arming or disarming (horn honk output)
– transmitter-controlled,
-
automatic re-arming of the security system after any unintentional disarming (arming up),
-
alternative arming of the security system without activation of additional sensors (additional
sensors bypass) – enables to leave children or pets inside a locked vehicle,
-
scanning of door switches and limit switches in 5 seconds or 44 seconds (option) after arming
the alarm system,
-
alarm memory – on disarming, provides information that the security system has been
triggered,
-
PRE-ALARM – warning signal,
-
signalling of improperly closed vehicle door upon the security system activation,
-
signalling of faulty sensors upon the security system activation,
-
faulty sensor bypass upon the security system activation,
-
valet mode, makes it possible to handle the vehicle over for service with no need to disclose
where the hidden button that disable identification system are located.
-
checking of the number, how many transmitters have been logged into the central control unit,
-
remote activation, by means of a single transmitter, both the vehicle security system and other
appliances (e.g. gates, house security systems).
2. INSTALLATION OF THE SECURITY SYSTEM
The vehicle security system is designed to protect your car against theft or robbery. By means of
both audible (siren chirp) and visual (turning lights flashing) it informs the car proprietor and all the
people nearby about any attempt to take unauthorized control over the vehicle. Triggering of the
alarm results also in disabling the engine ignition to prevent driving the vehicle by an offender.
Installation of the security system should be carried out by a qualified technician, in accordance
with the manufacturer’s instructions included into the installation manual.
Do not attempt to install the system yourself as only professional installation ensures proper
operation of the entire system.
3. SETUP OF THE SECURITY SYSTEM
To take advantage of all the features of your security system all the additional sensors should be
connected, such as ultrasonic detectors of movements, radar detectors of movements, shock
detectors, sensor of broken glass panels, towing attempts detectors, etc.
The security system, if installed without additional sensors, is triggered only by opening the
vehicle doors (door switches) and the trunk or hood sensors (if installed).
super
FORTECA
ver. E20(01)
1
4. INSTRUCTIONS FOR A USER
ALARM DISARMED
4.1. Arming of the system
: press the
[A]
button of the transmitter.
RESULT: single long flash of turning lights, single chirp of a siren (provided for the audible
signalization is activated), actuation of the central lock – door locked, the LED on the driver’s
dashboard stars blinking 3 times per second – arming in progress, and after 22 seconds the LED
blinks once per second – the security system is armed.
4.1.1. Silent arming of the system.
If the option of the system arming /disarming
confirmation by a siren chirp is set, press and hold the
[A]
button longer than two
seconds. The security system shall get armed but no siren chirp is to be heard.
4.1.2. Loud arming of the system.
If the option of silent arming /disarming of the system is
set, press and hold the
[A]
button longer than two seconds. The security system shall
get armed with a single siren chirp confirmation.
4.2. Warning on improperly closed door:
If the arming button
[A]
of the terminal has been
depressed and the system responds with four fast siren chirps one of the vehicle doors is not
closed properly or one of the door limit switches is defective.
4.3. Warning on faults of additional sensors:
If the arming button
[A]
of the terminal has been
depressed and the system responds with three fast siren chirps one of additional sensors is
defective.
4.4. Warning on faults of PRE-ALARM sensors:
If the arming button
[A]
of the terminal has been
depressed and the system responds with six fast siren chirps the PRE-ALARM sensor is
defective.
NOTE:
Warning on improperly closed door as well as on defective sensors is always
confirmed with siren chirps, in spite of whichever option of arming confirmation has been set
(silent or loud).
4.5. Additional sensors bypass:
Press the
[A]
button while the turning light are on.
RESULT: a single siren chirp, inputs of additional sensors and pre-alarm system disabled,
however power supply outputs to relevant sensors remain active.
ALARM ARMED
4.6. Disarming of the system
: press the
[A]
button of the transmitter.
RESULT: actuation of the central lock – door unlocked, two siren chirps (provided for the audible
signalization is activated), turning lights flash twice, the LED on the driver’s dashboard goes off.
4.6.1. Silent disarming of the system.
If the option of the system arming /disarming
confirmation by a siren chirp is set, press and hold the
[A]
button longer than two
seconds. The security system shall get disarmed but no siren chirp is to be heard.
4.6.2. Loud disarming of the system.
If the option of silent arming /disarming of the system
is set, press and hold the
[A]
button longer than two seconds. The security system shall
get disarmed with siren chirps confirmation.
4.6.3. Alarm triggering
super
FORTECA
ver. E20(01)
2
After opening the vehicle door (min. 0.7 sec) the siren signal is given and turning lights
blink for 30 seconds as well as ignition gets disabled.
Activation of an additional sensor (min. 0.5 sec.) results in releasing a siren signal and
turning lights blinking for 30 seconds.
Turning on the ignition key to the IGN position (min. 0.7 sec.) results in releasing a siren
signal and turning lights blinking for 30 seconds as well as ignition gets disabled.
Triggering the pre-alarm sensor (min. 0.5 sec.) results in a series of pre-warning siren
chirps (deterring alarm).
During a single guarding cycle (after arming the security system) there is a limitation for
door switches and additional sensors triggering. Each of the switches and sensors can
be triggered not more than 10 times and every next triggering results in disabling the
relevant input.
The pre-alarm input can be re-triggered only in the reason for its triggering is found out
(protection against repeated triggering by a defective sensor).
4.7. Alarm memory
: if additional siren chirps are heard upon disarming, the security system has
been triggered during the guarding cycle:
-
one chirp – the inputs from additional sensors had been activated,
-
two chirps – the inputs from door switches had been activated.
NOTE:
Warnings from the alarm memory are always confirmed with siren chirps, in spite of
whichever option of arming confirmation has been set (silent or loud).
4.8. Triggered alarm silencing
: press the
[A]
button of the transmitter.
4.8.1.
Press the
[A]
button of the transmitter.
RESULT: Warning signals go off, the security system remains armed and the central
lock still locks the vehicle door.
4.9. PANIC function (independent on the current status of the system – armed /disarmed)
press the
[B]
button of the transmitter.
RESULT: the panic mode is activated (the siren wails for 30 seconds, turning lights blink,
however ignition is enabled).
4.9.1. PANIC function de-activation:
Press the
[B]
button of the transmitter.
RESULT: the siren goes off and turning lights stop blinking.
4.10. Automatic re-arming:
disarm the security system and prevent from opening the vehicle door.
RESULT: the LED on the dashboard blinks twice per second. Unless the door is opened, after
thirty second delay the security system is armed again (the alarm protects the vehicle and the
central lock is locked)
4.11. The two-stage COMFORT function:
4.11.1.
Activation of the function (1
st
stage):
Press and hold the
[A]
button of the transmitter longer than two seconds while the
ignition key is ON.
super
FORTECA
ver. E20(01)
3
RESULT: the LED on the dashboard blinks once, the COMFORT function (1
st
stage)
is activated, the central lock is actuated (door locked) after the 6 second delay.
Since the function is activated, every time if the ignition key in turned on to the
IGN position the central lock is actuated after 5 second delay. Otherwise, after
killing the engine (the ignition key turned off) the door lock opens in two
seconds.
If the function is activated (door is locked),
the door is not re-locked
after
opening and shutting the vehicle door from inside (e.g. after getting the
passenger off).
4.11.2.
Activation of the function (2
nd
stage):
After having the first stage of the COMFORT function activated and while the ignition
key is ON, press and hold the
[A]
button of the transmitter longer than two seconds
before the central lock gets actuated
.
RESULT: the LED on the dashboard blinks once, the COMFORT function (2
nd
stage)
is activated,
Since that time the COMFORT function is interconnected with the door
switches! If the function is activated (door is locked), every time when the door
is opened from inside (e.g. when a passenger gets off)
the central lock is
released and then re-locked after having the vehicle door shut.
NOTE! Be extremely careful not to leave the vehicle keys inside the cabin!
4.11.3.
De-activation of the COMFORT function:
Press and hold the
[C]
button of the transmitter longer than two seconds while the
ignition key is ON.
RESULT: the LED on the dashboard blinks twice, the COMFORT function (both 1
st
and 2
nd
stages) is de-activated, the central lock is actuated (door unlocked).
4.12. Using an additional output channel
-
in the neutral mode (the security system disarmed) press the
[C]
button of the transmitter
RESULT: a negative pulse (ground) with 1 second duration appears at the output of the
additional channel, the turning lights and the dashboard LED flash for two seconds (if the
ignition key is in the ON position the turning lights do not flash, only the dashboard LED goes
ON).
-
if the re-arming function is active, the feature results in de-activation of that function (re-arming
disabled),
-
if the security system is armed the feature results in disarming of the system with simultaneous
activation of the additional channel output,
4.13. The valet mode
Before handing the vehicle over for service the security system should be switched to the valet mode.
super
FORTECA
ver. E20(01)
4
4.13.1. Activation of the valet mode:
-
shut the vehicle door,
-
turn the ignition key to the ON position.
-
press simultaneously the
[B]
and
[C]
buttons of the transmitter and hold them
depressed for more than 4 seconds,
-
after 4 seconds when the siren chirps and the dashboard LED goes permanently
ON, release the buttons of the transmitter,
-
the valet mode is activated,
In the valet mode the transmitter actuates only the central lock feature while the
ignition is always enabled. The vehicle can be handed over for service without the
identifying transmitters and locations of the hidden authorization button need not to be
disclosed.
The valet mode remains in force even if the power supply of the security system
is cut off.
4.13.2. De-activation of the valet mode:
-
shut the vehicle door,
-
turn the ignition key to the ON position.
-
press simultaneously the
[B]
and
[C]
buttons of the transmitter and hold them
depressed for more than 4 seconds,
-
after 4 seconds the siren chirps will be heard (the number if chirps corresponds to
the number of transmitters that are logged into the security system!)
-
the dashboard LED goes OFF,
-
release the transmitter buttons,
-
the valet mode is de-activated,
5. ADDITIONAL FEATURES
NOTE
:
Prior to take advantage of the
additional features
the user must have them activated.
5.1 Entering the mode of programming the
user’s options
Disarm the security system, open the vehicle door and turn the ignition key ON (if the driver
identification function is active the last should be cancelled), then press simultaneously the
[B]
and
[C]
buttons of the transmitter
RESULT: The dashboard LED starts fast blinking, the programming mode is activated.
5.2 Quitting the mode of programming the
user’s options
Turn the ignition key off or shut the vehicle door
RESULT: The dashboard LED goes off.
5.3 Selection of the loud or silent arming /disarming mode of the security system
Enter the mode of programming the user’s options (par. 5.1) then press the
[B]
button of the
transmitter.
RESULT:
super
FORTECA
ver. E20(01)
5
[ Pobierz całość w formacie PDF ]