Samsung SGH-E830 service manual, samsung service manuals schematy serwisowki
[ Pobierz całość w formacie PDF ]
GSM TELEPHONE
SGH-E830
GSM TELEPHONE
CONTENTS
1. Safety Precautions
2. Specification
3. Product Function
4. Array course control
5. Exploded View/Disassembly
and Assembly Instructions
6. MAIN Electrical Parts List
7. Block Diagrams
8. PCB Diagrams
9. Flow Chart of Troubleshooting
10. Reference data
1.
Safety Precautions
1-1. Repair Precaution
―
Repair in Shield Box, during detailed tuning.
Take specially care of tuning or test,
because specipicty of cellular phone is sensitive for surrounding interference(RF noise).
―
Be careful to use a kind of magnetic object or tool,
because performance of parts is damaged by the influence of magnetic force.
―
Surely use a standard screwdriver when you disassemble this product, otherwise screw
will be worn away.
―
Use a thicken twisted wire when you measure level.
A thicken twisted wire has low resistance, therefore error of measurement is few.
―
Repair after separate Test Pack and Set because for short danger (for example an
overcurrent and furious flames of parts etc) when you repair board in condition of
connecting Test Pack and tuning on.
―
Take specially care of soldering, because Land of PCB is small and weak in heat.
―
Surely tune on/off while using AC power plug, because a repair of battery charger is
dangerous when tuning ON/OFF PBA and Connector after disassembling charger.
―
Don't use as you pleases after change other material than replacement registered on SEC
System.
Otherwise engineer in charge isn't charged with problem that you don't keep this rules.
1-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
S
afety Precautions
1-2. ESD(Electrostatically Sensitive Devices) Precaution
Several semiconductor may be damaged easily by static electricity. Such parts are called by
ESD(Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below.
You can prevent from ESD damage by static electricity.
―
Remove static electricity remained your body before you touch semiconductor or parts
with semiconductor. There are ways that you touch an earthed place or wear static
electricity prevention string on wrist.
―
Use earthed soldering steel when you connect or disconnect ESD.
―
Use soldering removing tool to break static electricity. , otherwise ESD will be damaged
by static electricity.
―
Don't unpack until you set up ESD on product. Because most of ESD are packed by box
and aluminum plate to have conductive power,they are prevented from static electricity.
―
You must maintain electric contact between ESD and place due to be set up until ESD is
connected completely to the proper place or a circuit board.
1-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
2. Specification
2-1. GSM General Specification
GSM900
Phase 1
EGSM 900
Phase 2
DCS1800
Phase 1
PCS1900
Freq. Band[MHz]
Uplink/Downlink
890~915
935~960
880~915
925~960
1710~1785
1805~1880
1850~1910
1930~1990
ARFCN range
1~124
0~124 &
975~1023
512~885
512~810
Tx/Rx spacing
45MHz
45MHz
95MHz
80MHz
Mod. Bit rate
/BitPeriod
270.833kbps
3.692us
270.833kbps
3.692us
270.833kbps
3.692us
270.833kbps
3.692us
Time Slot Period
/FramePeriod
576.9us
4.615ms
576.9us
4.615ms
576.9us
4.615ms
576.9us
4.615ms
Modulation
0.3GMSK
0.3GMSK
0.3GMSK
0.3GMSK
MS Power
33dBm~5dBm
33dBm~5dBm
30dBm~0dBm
30dBm~0dBm
P o w e r C l a s s
5 p c l ~ 1 9 p c l
5pcl ~ 19pcl
0pcl ~ 15pcl
0pcl ~ 15pcl
Sensitivity
-102dBm
-102dBm
-100dBm
-100dBm
TDMA Mux
8
8
8
8
Cell Radius
35Km
35Km
2Km
-
2-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Specification
2-2. GSM TX power class
TX Power
control level
GSM900
TX Power
control level
DCS1800
TX Power
control level
PCS1900
5
33±2 dBm
0
30±2 dBm
0
30±2 dBm
6
31±3 dBm
1
28±3 dBm
1
28±3 dBm
7
29±3 dBm
2
26±3 dBm
2
26±3 dBm
8
27±3 dBm
3
24±3 dBm
3
24±3 dBm
9
25±3 dBm
4
22±3 dBm
4
22±3 dBm
10
23±3 dBm
5
20±3 dBm
5
20±3 dBm
11
21±3 dBm
6
18±3 dBm
6
18±3 dBm
12
19±3 dBm
7
16±3 dBm
7
16±3 dBm
13
17±3 dBm
8
14±3 dBm
8
14±3 dBm
14
15±3 dBm
9
12±4 dBm
9
12±4 dBm
15
13±3 dBm
10
10±4 dBm
10
10±4 dBm
16
11±5 dBm
11
8±4dBm
11
8±4dBm
17
9±5 dBm
12
6±4 dBm
12
6±4 dBm
18
7±5 dBm
13
4±4 dBm
13
4±4 dBm
19
5±5 dBm
14
2±5 dBm
14
2±5 dBm
15
0±5 dBm
15
0±5 dBm
2-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
[ Pobierz całość w formacie PDF ]